DELTA UNISAW MITER HOLDER

DELTA UNISAW MITER HOLDER DELTA UNISAW MITER HOLDER...ALWAYS KNOW WHERE YOUR MITER IS! This neat little item attaches to the underside of your Unisaw table and stores your miter conveniently, safely, and close at hand, but totally out of the way. THE GOOD THING.........THERE ARE NO HOLES TO DRILL IN YOUR VINTAGE UNISAW CABINET. Your miter usually lays on the saw's tabletop, so it is there when you need it.........but when you don't need it, you cart it off to the bench................ or anywhere else you can find a place to lay it down. Why not store it at the saw? This miter holder keeps your miter out of the way, close at hand, convenient, and safe from falling off the bench. The miter is easy to grip with the handle side down, easy to insert in the generous tube opening, doesn't rattle when the saw is running, and is stored with the miter's metal rail in contact with PVC... not metal to metal. This PVC tube, with its two brackets, bolts to the underside of the Unisaw's table using two of the existing tabletop's threaded bolt holes. This holder accommodates a stock miter or even our long bar billet aluminum miter (Both are shown in one of the photos and the difference is dramatic !!!). Plus, the location of this holder still allows our wrench hanger and wrench to stay conveniently in the designed position on the same right front tabletop bolt. This holder can be installed on either the left or right side of the saw.......or if you have a couple of miters and want to store both conveniently close by..... buy two. The position of the miter does not interfere with any of the saw's functions. The head of the miter does not protrude out past the fence guide rails, so it is not at all in the way when operating the saw. The easy-to-install miter holder comes preassembled with a gray heavy wall PVC tube, a pair of heavy-duty clamps, and a pair of 6061 aluminum brackets we had laser cut, drilled and tapped to match your exiting holes. Flat washers and longer bolts are included to replace the stock bolts when installing the holder to the underside of the table. With your miter conveniently stored in this holder under the saw's table, it is safe and secure. It can't fall from the bench or from the pile of boxes you laid it on. It can't be damaged, and the angular setting or the squareness of the miter won't be altered by a tumble onto the floor. Why would you not have one of these on your saw? Although this holder was designed to fit conveniently under the Delta Unisaw table, it will likely fit any table saw that has a couple of visible bolts securing the top to the saw's cabinet. The spacing between the brackets on this holder is totally adjustable. DELTA UNISAW MITER HOLDER...ALWAYS KNOW WHERE YOUR MITER IS! This neat little item attaches to the underside of your Unisaw table and stores your miter conveniently, safely, and close at hand, but totally out of the way. THE GOOD THING.........THERE ARE NO HOLES TO DRILL IN YOUR VINTAGE UNISAW CABINET. Your miter usually lays on the saw's tabletop, so it is there when you need it.........but when you don't need it, you cart it off to the bench................ or anywhere else you can find a place to lay it down. Why not store it at the saw? This miter holder keeps your miter out of the way, close at hand, convenient, and safe from falling off the bench. The miter is easy to grip with the handle side down, easy to insert in the generous tube opening, doesn't rattle when the saw is running, and is stored with the miter's metal rail in contact with PVC... not metal to metal. This PVC tube, with its two brackets, bolts to the underside of the Unisaw's table using two of the existing tabletop's threaded bolt holes. This holder accommodates a stock miter or even our long bar billet aluminum miter (Both are shown in one of the photos and the difference is dramatic !!!). Plus, the location of this holder still allows our wrench hanger and wrench to stay conveniently in the designed position on the same right front tabletop bolt. This holder can be installed on either the left or right side of the saw.......or if you have a couple of miters and want to store both conveniently close by..... buy two. The position of the miter does not interfere with any of the saw's functions. The head of the miter does not protrude out past the fence guide rails, so it is not at all in the way when operating the saw. The easy-to-install miter holder comes preassembled with a gray heavy wall PVC tube, a pair of heavy-duty clamps, and a pair of 6061 aluminum brackets we had laser cut, drilled and tapped to match your exiting holes. Flat washers and longer bolts are included to replace the stock bolts when installing the holder to the underside of the table. With your miter conveniently stored in this holder under the saw's table, it is safe and secure. It can't fall from the bench or from the pile of boxes you laid it on. It can't be damaged, and the angular setting or the squareness of the miter won't be altered by a tumble onto the floor. Why would you not have one of these on your saw? Although this holder was designed to fit conveniently under the Delta Unisaw table, it will likely fit any table saw that has a couple of visible bolts securing the top to the saw's cabinet. The spacing between the brackets on this holder is totally adjustable.eBay integration by

DELTA UNISAW MITER HOLDER

DELTA UNISAW MITER HOLDER...ALWAYS KNOW WHERE YOUR MITER IS! This neat little item attaches to the underside of your Unisaw table and stores your miter conveniently, safely, and close at hand, but totally out of the way. THE GOOD THING.........THERE ARE NO HOLES TO DRILL IN YOUR VINTAGE UNISAW CABINET. Your miter usually lays on the saw's tabletop, so it is there when you need it.........but when you don't need it, you cart it off to the bench................ or anywhere else you can find a place to lay it down. Why not store it at the saw? This miter holder keeps your miter out of the way, close at hand, convenient, and safe from falling off the bench. The miter is easy to grip with the handle side down, easy to insert in the generous tube opening, doesn't rattle when the saw is running, and is stored with the miter's metal rail in contact with PVC... not metal to metal. This PVC tube, with its two brackets, bolts to the underside of the Unisaw's table using two of the existing tabletop's threaded bolt holes. This holder accommodates a stock miter or even our long bar billet aluminum miter (Both are shown in one of the photos and the difference is dramatic !!!). Plus, the location of this holder still allows our wrench hanger and wrench to stay conveniently in the designed position on the same right front tabletop bolt. This holder can be installed on either the left or right side of the saw.......or if you have a couple of miters and want to store both conveniently close by..... buy two. The position of the miter does not interfere with any of the saw's functions. The head of the miter does not protrude out past the fence guide rails, so it is not at all in the way when operating the saw. The easy-to-install miter holder comes preassembled with a gray heavy wall PVC tube, a pair of heavy-duty clamps, and a pair of 6061 aluminum brackets we had laser cut, drilled and tapped to match your exiting holes. Flat washers and longer bolts are included to replace the stock bolts when installing the holder to the underside of the table. With your miter conveniently stored in this holder under the saw's table, it is safe and secure. It can't fall from the bench or from the pile of boxes you laid it on. It can't be damaged, and the angular setting or the squareness of the miter won't be altered by a tumble onto the floor. Why would you not have one of these on your saw? Although this holder was designed to fit conveniently under the Delta Unisaw table, it will likely fit any table saw that has a couple of visible bolts securing the top to the saw's cabinet. The spacing between the brackets on this holder is totally adjustable.

DELTA UNISAW UNDER-TABLE MITER-GAUGE HOLDER

Always know where your miter gauge is.

This holder mounts beneath the table of a compatible vintage Delta Unisaw, keeping your miter gauge conveniently within reach while safely out of the way.

NO DRILLING REQUIRED:

The holder installs using two existing threaded table-mounting holes. No holes need to be drilled in the Unisaw cabinet or table.

The heavy-wall PVC tube provides a generous opening that makes the miter gauge easy to insert and remove. The gauge is stored with its steel bar resting against PVC rather than metal, helping prevent rattling while the saw is running.

FEATURES:

Convenient under-table storage
No drilling or permanent modification required
Uses existing threaded mounting holes
Heavy-wall gray PVC storage tube
Adjustable bracket spacing
Can be installed on the left or right side of the saw
Does not extend beyond the fence-guide rails
Does not interfere with normal saw operation
Compatible with an original Delta miter gauge or our long-bar billet-aluminum miter gauge
Allows our Unisaw wrench hanger to remain installed on the right-front table bolt

INCLUDED:

One heavy-wall gray PVC storage tube
Two heavy-duty tube clamps
Two laser-cut and machined 6061 aluminum mounting brackets
Two flat washers
Two longer mounting bolts

The holder arrives preassembled for straightforward installation.

IMPORTANT:

This listing is for one miter-gauge holder and its mounting hardware. The Unisaw, miter gauges, wrench, wrench hanger, fence rails, and all other components shown are not included.

One holder stores one miter gauge. Install one on each side of the saw if you want convenient storage for two gauges.

This holder was designed for compatible Delta Unisaw's. It may fit other table saws with accessible table-mounting bolts, but compatibility with other machines is not guaranteed. Please compare the available mounting locations and clearances on your saw before ordering.

Brand	vintagedeltasupply
Country of Origin	United States

DELTA UNISAW MITER HOLDER

Shipping

Specifications